2650-1168
Good Engine
Ground
White or Clear (16 pulse/revolution, Square Wave)
Red (12V Positive from Ignition Switch)
Black
Drive Key
Installation Nut
7/8-18 thread
Remove cap for cruise control cable,
otherwise leave cap installed.
Supplied with .104 sq x .104 sq
Transmission
Take-off
12 MONTH LIMITED WARRANTY
Auto Meter Products, Inc. warrants to the consumer that all Auto Meter High Performance products will be free from defects in material and workmanship for a period of twelve (12) months from date of the original
purchase. Products that fail within this 12 month warranty period will be repaired or replaced at Auto Meter’s option to the consumer, when it is determined by Auto Meter Products, Inc. that the product failed due
to defects in material or workmanship. This warranty is limited to the repair or replacement of parts in the Auto Meter instruments. In no event shall this warranty exceed the original purchase price of the Auto
Meter instruments nor shall Auto Meter Products, Inc. be responsible for special, incidental or consequential damages or costs incurred due to the failure of this product. Warranty claims to Auto Meter must be
transportation prepaid and accompanied with dated proof of purchase. This warranty applies only to the original purchaser of product and is non-transferable. All implied warranties shall be limited in duration to
the said 12 month warranty period. Breaking the instrument seal, improper use or installation, accident, water damage, abuse, unauthorized repairs or alterations voids this warranty. Auto Meter Products, Inc.
disclaims any liability for consequential damages due to breach of any written or implied warranty on all products manufactured by Auto Meter.
FOR SERVICE CONTACT: AUTO METER PRODUCTS Inc. 413 W. Elm St., Sycamore, IL 60178 USA (815) 899-0801 or
2650-1168 7/24/06
Red (12V Positive from Ignition Switch )
Good Engine
Ground
Remove cap for cruise control cable,
otherwise leave cap installed.
Retaining Clip for cruise control cable
Black
Drive Key
Mounting Bracket
Existing Bolt
Transmission
Take-off
White or Clear
(16 pulse/revolution, Square Wave)
INSTALLATION INSTRUCTIONS
HALL-EFFECT ELECTRIC
SPEEDOMETER SENDERS
(SQUARE WAVE)
3 Wire Sender, with Optional Cable Hook-Up
QUESTIONS:
If after completely reading these instructions you have questions regarding the operation or installation of your instrument(s),
please contact Auto Meter Technical Service at 815-899-0801.
You may also email us at service@autometer.com.
Additional information can also be found at http://www.autometer.com/tech_faq.aspx
© 2006 Auto Meter Products, Inc.
SERVICE
For service send your product to Auto Meter in a well packed shipping carton. Please include a note explaining what the problem is along with your phone number. Please specify when you need
the product back. If you need it back immediately mark the outside of the box “RUSH REPAIR,” and Auto Meter will service product within two days after receiving it. ($10.00 charge will be added
to the cost of “RUSH REPAIR.”) If you are sending product back for Warranty adjustment, you must include a copy (or original) of your sales receipt from the place of purchase.
Model 5292 (Ford Models Only)
Steps for installation:
1. Remove stock speedometer cable.
2. Remove c-clip off of cable.
3. Remove nylon gear.
4. Install drive key into sender.
5. Install gear on sender.
6. Install c-clip on sender.
7. Insert sender into transmission.
8. Tighten mounting bracket to the transmission with the
existing bolt.
9. Wire sender as shown.
Model 5291
Steps for installation:
1. Place Drive Key in sender.
2. Place sender on Transmission Take-off.
3. Tighten Installation Nut.
4. Wire sender as shown.
(2 pages)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels